UNiKA PRO IS2
126,65 €
ADÓT TARTALMAZ
Passive dual isolator, 2 x combo jacks, 2 x XLR with ISO transformer, rugged steel housing
Ingyenes kiszállítás több ezer termékre
100%-ban biztonságos online fizetés
30 nap áll rendelkezésre az áru visszaküldésére
Passive dual isolator
- CH1 and CH2 INPUT-XLR /TRS Combi connects the outputs of a mixer, preamp, or other line-level source to the PRO-IS2. CH1 and CH2 have separate audio paths and can therefore be used independently.
- REV - reverses the polarity of CH2. If the input is wired to pin 3 (hot), pressing REV will change the polarity to pin 2 (hot).
- CH1 and CH2 OUTPUT-XLRs connect the transformer-isolated balanced audio signal to monitor mixers, recording equipment, powered speakers, external effects, and other line-level devices via a standard XLR cable.
- GND/LIFT- Pressing GRND-1 cuts the ground at the output of the CH1 transformer to prevent hum and noise from ground loops. GRND-2 interrupts the ground at the output of CH2.
- Rugged steel housing - with scratch resistant paint finish.
- Anti-slip mat - a full-surface, flexible foam rubber mat cushions and stabilizes the PRO-IS2.
UNiKA PRO-IS2 at a glance
The UNiKA PRO-IS2 is a professional passive isolator that converts two separate line-level signals into two independent, transformer-isolated, balanced outputs. This allows a signal from a submixer, monitor mixer, preamp, or other mains-powered audio source to be connected to mixers, recorders, powered speakers, and outboard effects in a way that isolates hum loops or influxes.
Because the PRO-IS2 is a passive device, no batteries or other power supplies are required, and UNiKA PRO's specially modified audio isolation transformer ensures pristine audio quality.
The heart - the UNiKA Pro EI9AE3R3 1.25:1 Audio Isolation Transformer
This is a modified, custom design with a special copper foil layer and a dedicated grounding layer.The design provides high musicality through a sound rich in overtones. Ground noise and leakage currents caused by potential differences are minimized and low impedance balanced outputs allow long cable runs with the best audio quality. A separate induction transformer powers the active circuitry in the PRO-148 and PRO-248, which is the proven, high-quality OEP PT-4 unit manufactured in the UK. The combination with the isolation transformer extends the flexibility and performance of the PRO-148 and PRO-248 compared to active designs that use only an induction transformer.
The UNiKA PRO-IS2 is equally at home on stage or in the studio with rugged steel housing, full anti-slip mat and recessed connectors
Technical data
- Circuit principle: Passive with transformer-balanced output
- Input connection: 2 x combination sockets
- Polarity reversal CH2: pressure switch
- Input impedance: 4.7 kOhm balanced / 10 kOhm unbalanced
- Output impedance: 600 Ohm
- Maximum input level before overload: +22 dB
- Maximum output level: +22 dB
- Output connectors: 2 x XLR with ISO transformer
- Output with split GND/LIFT switch
- Frequency response: 20 Hz - 20 kHz, -0.3/+0.1 dB
- S/N ratio @20 Hz - 20 kHz, unweighted: > 120 dB
- THD @ 1 kHz, 0 dB output: < 0.02%.
- Isolation transformer type: 1.25:1
- Housing: 1.6 mm / 1.2 mm steel
- Finish: Scratch resistant paint
- Dimensions (W x D x H): 78 x 124 x 46 mm
- Weight: 0.62 kg
PAH0023414-000
Adatlap
- Signal Processing
- Passive
- Manufacturer
- Unika
GYAKRAN EGYÜTT VÁSÁROLT
TERMÉKEK AZONOS MÁRKÁBÓL
Passive dual isolator, 2 x combo jacks, 2 x XLR with ISO transformer, rugged steel housing
UNiKA PRO IS2
126,65 €
ADÓT TARTALMAZ